Learn how to use the DCT700 with a VCR. The Shaw DCT700 can be used in conjunction with a traditional VCR.
- Comcast Motorola Dct700 Cable Box
- How To Unlock Motorola Dct700 Cable Box Tv
- Motorola Model Dct700
- Motorola Cable Box Dct700
This article will provide insight into:
How to set up your DCT700 to a VCR | |
---|---|
The setup described below will allow users the ability to watch TV via the DCT700, record programming from the DCT700 to a VHS tape, and to continue viewing their library of VHS tapes. This guide assumes that the DCT700 and VCR will be connected via the same coaxial connection and sharing a single coaxial connection (Channel 3. Channel 4 in Edmonton) on the television set. To make the correct connections, please follow these steps:
Here is a wiring diagram that corresponds to the steps listed above: (click image below for an expanded view) License key for malwarebytes 3.0.4 mac. If you are unsure of what a coaxial cable looks like, please refer to the photo below. Note the center pin and threaded screw-on connector. To properly use this configuration, please confirm that all components are powered on and that the TV and VCR are currently set to channel 3 (channel 4 in Edmonton). Setting both the VCR and television to channel 3 will allow both to view the picture from the box. You will be able to tune to any available channel through the box and view it on screen providing the TV and VCR are tuned to channel 3 (channel 4 in Edmonton). |
Comcast Motorola Dct700 Cable Box
1 AUDIO OUT Left/right audio outputs to connect the DCT700 to a TV, VCR, or A/V receiver. 2 VIDEO Composite video output to connect the DCT700 to a TV, VCR, or A/V receiver. 3 RF IN A coaxial input that is connected to the cable wall outlet, see Connecting the DCT700. 4 TO TV/VCR A coaxial output to connect the DCT700 to the TV or VCR.
- DCT700: Make sure that you've reset the unit. Hold down any button on the remote control, then disconnect and reconnect the power cord. Wait for the box to reboot. Press the '3' key when the 'Power' LED light on the front of the box begins flashing. You must press '3' within three seconds.
- Apr 21, 2013 I just bought a DCT700/MX2 digital cable set box from my cable supplier, and for one month they are giving me open signal for all channels (except PayPerView's), I assume there would be a way in which I could unlock the cable signal receiver in order to get all the channels.
- Note Motorola cable boxes are sold exclusively to cable companies in the United States. The DCT and QIP boxes cannot be purchased or ordered by consumers in the states. All DCT700 and QIP boxes on ebay and craigslist were stolen at some point, and only rarely do the cable companies ever receive any form of compensation from the customer (less.
How to set a recording | |
---|---|
Once you have followed the above connection you can use your DCT700 to plan an upcoming recording and tune to the correct channel so your VCR can implement the actual recording. In this example we will be setting the DCT700 and VCR to record a show on channel 6 at 6pm:
|
How To Unlock Motorola Dct700 Cable Box Tv
Related Articles
Shaw Digital Boxes Equipment Guide |
How to reset Motorola DCT700 October 19, 2009
Motorola Model Dct700
Posted by mylinuxtips in Digital Cable Box, GeneralPost.trackback
Motorola Cable Box Dct700
Set-top Cold Initialization
The DCT700 has no front panel buttons. To perform a cold initialization, or reset, using the
remote control:
1
Hold down any key while disconnecting and reconnecting AC power to the set-top.
After booting up, the
POWER
LED on the set-top front panel flashes.
2
Within 3 seconds, press 3.
The
POWER
LED flashes at a decreased rate.
3
Within 3 seconds, press 2.
The
POWER
LED flashes at an increased rate.
4
Within 3 seconds, press 8 to initiate the cold reset.
During the cold initialization procedure, if the appropriate remote control key is not pressed
within the three-second time period, the procedure terminates and the set-top resumes
normal operation
The DCT700 has no front panel buttons. To perform a cold initialization, or reset, using the
remote control:
1
Hold down any key while disconnecting and reconnecting AC power to the set-top.
After booting up, the
POWER
LED on the set-top front panel flashes.
2
Within 3 seconds, press 3.
The
POWER
LED flashes at a decreased rate.
3
Within 3 seconds, press 2.
The
POWER
LED flashes at an increased rate.
4
Within 3 seconds, press 8 to initiate the cold reset.
During the cold initialization procedure, if the appropriate remote control key is not pressed
within the three-second time period, the procedure terminates and the set-top resumes
normal operation